SEKURE Paradox Digiplex DGP-610 Installationshandbuch

Digiplex Control PanelReference & Installation Manual

- 9 -the zone’s parameters must be defined. Please refer toZone Programming in section 5 for more information.The keypad will communicate the status o

- 10 -2.13 CONNECTING THE ZX4The ZX4 is a 4-Zone Expansion Module that connects directly to the control panel through its on-boardEXPANSION connector

- 11 -2.14 KEYSWITCH CONNECTIONSConnect the keyswitches to the keypad, controlpanel, or Zone Expander Module’s hardwired-inputterminals as shown in f

- 12 -PROGRAMMING METHODThe Digiplex Control Panel can be programmed usingthe Paradox Upload/Download Software forWindows or manually by using a keyp

- 13 -ACCESS CODESThe Digiplex control panel supports the followingaccess codes:• 63 User Access Codes• 1 System Master Code• 1 Installer Code.4.1

- 14 -4.4.2 DuressSections [802] to [864] – Option [3]When a user is forced to arm or disarm their system,entering a Duress enabled User Access Code (

- 15 -ZONE PROGRAMMINGAll detection devices, whether connected to the control panel, keypads or zone expander modules must beassigned to a zone and th

- 16 -5.1 ZONE NUMBERINGSections [001] to [048]The Zone Numbering feature allows you to assignany detection device in the system, to any of the 48zone

- 17 -will not enable the bell/siren output. Enter any validaccess code on the keypad to stop the buzzer.Only keypads assigned to the same partitionas

- 18 -5.4.1 Auto Zone ShutdownSections [101] – [148]: Option [1]If, in a single armed period, an Auto Zone Shutdownzone communicates more than the num

- 1 - TABLE OF CONTENTSTABLE OF CONTENTS...

- 19 -does not apply to bus detectors connected to theDIGI-BUS.Example:The system is armed and the zone speed is set for600m seconds. A zone opens and

- 20 -KEYSWITCH PROGRAMMINGThe Digiplex Control Panel can support up to 8 keyswitch zones in addition to 48 standard zones. A keyswitchallows a user t

- 21 -6.1 KEYSWITCH NUMBERINGSections [049] to [056]The Keyswitch Numbering feature allows you toassign any hardwired-input in the system, to any ofth

- 22 -Force Zones (see section 5.4.4) at the time ofarming. For more information on Force Arming, referto section 14.6.4.4 Instant Arming (Keyswitch

- 23 -ARMING & DISARMING OPTIONS7.1 ARMING FOLLOWS PARTITIONSections [505], [509], [513], [517]: Options [1] to [4]A partition can be set to follo

- 24 -7.5.1 No Movement TimerSections [222] to [225]: 001-255 X 15min.If No Movement Auto-Arming is enabled (see section7.5), the control panel send t

- 25 -Program the number of consecutive invalid codesfrom 001 to 255 (000=disabled) into section [220].Program the duration of the keypad lockout fro

- 26 -ALARM OPTIONS8.1 BELL/ALARM OUTPUTSection [500]: Options [5] to [8]When a partition generates an alarm, the controlpanel can toggle the onboard

- 27 -Recognition) if a tamper or wire fault occurs on abypassed zone.8.4 KEYPAD PANIC OPTIONSSections [506], [510], [514], [518] - Options [1] to [6]

- 28 -EVENT REPORTING[0]Ademco Slow[3]Ademco ExpressPulse[1]Silent Knight Fast[2]SescoaDTMF(Tone)Program 2-digit (00-FF)report codes into sections[60

- 2 -7.4 TIMED AUTO ARMING...

- 29 -9.1 REPORTING ENABLEDSection [521]: Option [3]This option will either enable or disable eventreporting. With option [3] on in section [521] eve

- 30 -9.2.5 Zone Alarm Report CodesSections [639] to [650]A report code can be programmed for each of theforty-eight available zones. Whenever a zoneg

- 31 -§ Module Battery Failure: Bus Power SupplySection [694]§ Module Auxiliary Failure: Bus Power Supply§ Wireless Module Battery Low§ Wireless M

- 32 -Account Codes for partitions 1 through 4. Partitionaccount numbers can be any hexa-digit from 0 to F.Example:If a zone generates an alarm in Par

- 33 -9.6.1 Maximum Dialing AttemptsSection [257]: 001-255The number (000=8; 001-255) programmed intosection [257] determines how many times the contr

- 34 -9.12 PAGER DELAYSection [259]When using the Pager Reporting Format (see section9.5.5), the control panel will wait for the delay period(001 to 0

- 35 -DIALER OPTIONS10.1 TELEPHONE LINE MONITORINGOptions [1] & [2] - Section [520]When enabled, the system verifies the existence of atelephone l

- 36 -PROGRAMMABLE OUTPUTSA PGM is a programmable output that toggles to itsopposite state (i.e. a normally open PGM will close)when a specific event

- 37 -Option OFF = Follow:1. If the first digit of the PGM Activation Event is setat 1, 2, 3, 4, 5, 6, or 7, the PGM will remainactivated until the P

- 38 -PGM Programming TableNote1*: 0 = All partitions enabled in the system (see section 12.6)1 = Partition 1 3 = Partition 32 = Partition 2 4 = Parti

- 3 -12.13 MODULE BROADCAST ...

- 39 -Feature Select ProgrammingFirstDigitEvent SecondDigit 1 2 3 4 5 6 7 80 Code # 1 Code # 2 Code # 3 Code # 4 Code # 5 Code # 6 Code # 7 Code # 81

- 40 -Feature Select ProgrammingFirstDigitEvent SecondDigit 1 2 3 4 5 6 7 84 Zone # 33 Zone # 34 Zone # 35 Zone # 36 Zone # 37 Zone # 38 Zone # 39 Zon

- 41 -SYSTEM SETTINGS & COMMANDS12.1 HARDWARE RESETPerforming a hardware reset will set the InstallerCode, the System Master Code to factory defau

- 42 -• User #49 is assigned to partition 4 with the Master Feature,Bypass Programming, Force and Stay Arming enabledUser #50 to 64 are assigned to p

- 43 -[FORCE] – CALL UPLOAD/DOWNLOAD SOFTWARE:Will dial the PC telephone number programmed insection [560] in order to initiate communication will aco

- 44 -screen. If any missing modules are detected (i.e.detector removed from the bus) during this scan, thecontrol panel will erase the module’s seria

- - 45 - -UPLOAD/DOWNLOAD SOFTWARE13.1 PANEL ANSWER OPTIONSSections [451] & [452]The following two options define how the controlpanel answers an

- 46 -13.6 ANSWER UPLOAD/DOWNLOADSOFTWAREIn order to perform on-site upload/download connectyour computer directly to the control panel using anADP-1

- - 47 - -USER/KEYPAD FEATURESThis section will be included in future revisions of this manual. For the moment, all information that has beenreference

- - 48 - -FCC WARNINGSIMPORTANT INFORMATIONThis equipment complies with Part 68 of the FCC rules subpart D and CS-03. Inside the cover of this equipme

- 4 -INTRODUCTIONParadox Security Systems has once-again redefinedthe boundaries of the security industry and is proudto introduce the Digiplex Contro

- 49 -ATTACHMENT LIMITATION NOTICEThe Industry Canada label identifies certified equipment. This certification means that the equipment meets certain

- - 50 - -INDEXAAC Fail, No Trouble Display... 44Access Code Length...

- 51 -Input terminal connections for zone doubling ... 9InstallationAdvanced Technology Zone (ATZ) Connections...

- 52 -System Trouble Restore Codes... 31Zone Tamper Codes...

- 5 -ZX8 Zone Expander Module (DGP-ZX8)Connected to the DIGI-BUS, this module will add 8hardwired-input terminals to the Digiplex System (16zones if

- 6 -INSTALLATION2.1 LOCATION & MOUNTINGBefore mounting the cabinet, push the five white nylon-mounting studs into the back of the cabinet. Pull a

- 7 -

- 8 -2.7 BELL/SIREN OUTPUTThe BELL+ and BELL- terminals power bells and/orother warning devices requiring a steady voltageoutput during an alarm. Th