SEKURE Paradox Spectra 1686H Installationshandbuch Seite 33
- Seite / 60
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SPECTRA SERIES 31
page 24). Only reports if Disarming Reporting Options (see page 36) are set to always r epor t disarming.
• REM O TE D ISARM : S y s t em i s d i s a r m e d u s i n g t h e W i nl o a d s o f t w a r e .
• KEYSWITCH DIS A RMI NG : System disarmed using a keyswitch (see page 19).
• Future use
8.2.5 ZONE ALAR M REPORT CODES
Sections [187] to [190]
A report code can be programmed for each of the 16 available zones. Whenever a zone generates an
alarm, the control panel can send the appropriate report code to the central station, identifying which zone
generated an alarm.
8.2.6 ZONE ALAR M RESTORE REPORT COD ES
Sections [191] to [194]
A report code can be programmed for each of the 16 available zones. The control panel can transmit these
report codes to the central station identifying which zone was restored.
A zone is restored when it closes after generating an alarm or once the bell has cut-off after al arm
generation. Please refer to Zone Restore Report Options on page 36.
8.2.7 SPECIAL ALAR M REPORT CODES
Sections [195] and [196]
Whenever the system generates an alarm due to one of the conditions listed below, the control panel can
send the appropriate report code to the central station identifying the type of alarm.
Section [195]
• EMERGEN CY PAN IC: Panic keys [1] and [3] have been pressed (see page 27).
• AUX IL IAR Y PANIC: Panic keys [4] and [6] have been pressed (see page 27).
• FIRE PANIC: Panic keys [7] & [9] have been pressed (see page 27).
• REC E NT CLOSING: Reports when an alarm is generated after arming the system within period defined
by the R ecent Close Delay ( see page 36).
Section [196]
• AUTO ZONE SHUTDOWN: A zone communicates more than the programmed number of transmissions
in a single armed period (see page 21).
• DURESS: A Duress access code is keyed in (see page 15).
• KEYPAD LOCKOUT: If a consecutive number of invalid codes are entered into a keypad, the control
panel can be set to deny access from all keypads for a specified period.
• Future use
8.2.8 ZONE TAMPER REPORT CODES
Section [197] to [200]
A report code can be programmed for each of the 16 available zones. Whenever a tamper or wire fault
occurs on a zone, the control panel can send the appropriate report code to the central station identifyi ng
which zone was tampered.
8.2.9 ZONE TAMPER RESTORE REP O RT CODES
Sections [201] to [204]
A report code can be programmed for each of the 16 available zones. Whenever a tampered zone is
restored, the control panel can send the appropriate report code to the central station identifying which
zone has been restored.
If Tamper Recognition (see page 27) is disabled, the control panel will not report the occurrence of
any tampers, wire faults or tamper restores.
8.2.10 SYSTEM TROUB LE REPORT CODES
Section [205] to [207]
Whenever the system generates one of the instances listed below, the control panel can send the
appropriate report code to the central station identifying the type of system trouble.
Section [205]
• Future use
• AC FAILURE: The control panel has detected a loss of AC pow er. Transmission of this report code can
- SPECTRA CONTROL PANELS V2.1 1
- TABLE OF CONTENTS 3
- LIST OF TABLES 4
- PART 1: INTRODUCTION 5
- PART 2: INSTALLATION 6
- 2.2 EARTH GROUND 7
- 2.3 AC POWER 8
- 2.4 BACKUP BATTERY 8
- 2.6 TELEPHONE LINE CONNECTION 8
- 2.7 BELL OUTPUT CONNECTION 9
- 2.9 SINGLE ZONE INPUTS 10
- 2.12 KEYSWITCH CONNECTIONS 11
- PART 3: PROGRAMMING METHODS 12
- SPECTRA SERIES 11 13
- PART 4: ACCESS CODES 15
- 4.1 ACCESS CODE LENGTH 16
- 4.4 USER CODE OPTIONS 16
- 4.6 DURESS CODE 17
- 4.5 LOCK MASTER CODE 17
- PART 5: ZONE PROGRAMMING 18
- 5.4 ZONE PROGRAMMING 19
- 5.5 ZONE DEFINITIONS 20
- 5.7 ZONE PARTITION ASSIGNMENT 22
- 5.8 ZONE OPTIONS 22
- 5.9 ZONE SPEED 24
- 5.10 EOL ZONES 24
- 6.1 SWITCH TO STAY AR MING 25
- 6.2 STAY ARMING WITH DELAY 25
- 6.6.1 AUT O-ARM TIMER 26
- 6.8 AUTO-ARMING OPTIONS 27
- 6.9 ONE-TOUCH ARMING 27
- 6.10 EXIT DELAY 27
- PART 7: ALARM OPTIONS 28
- 7.3 TAMPER RECOGNITION 29
- 7.4 KEYPAD PANIC OPTIONS 29
- 7.5 PANIC LOCKOUT TIMER 30
- SPECTRA SERIES 29 31
- 8.2 REPORT CODES 32
- Sections [208] to [210] 34
- Sections [211] to [213] 34
- 8.4 PARTITION ACCOUNT NUMBERS 35
- 8.5 REPORTING FORMATS 35
- 8.6 PAGER DELAY 36
- 8.7 EVENT CALL DIRECTION 36
- SPECTRA SERIES 35 37
- PART 9: PROGRAMMABLE OUTPUTS 39
- PART 10: SYSTEM SETTINGS 41
- 10.6 SYSTEM REAL-TIME CLOCK 42
- 10.7 CLOCK ADJUST 42
- SPECTRA SERIES 43 45
- 11.1 PANEL ANSWER OPTIONS 46
- 11.2 PANEL IDENTIFIER 46
- 11.3 PC PASSWORD 46
- 11.4 PC TELEPHONE NUMBER 46
- 11.5 CALL WINLOAD SOFTWARE 47
- 11.6 ANSWER WINLOAD SOFTWARE 47
- 11.8 CALL BACK WINLOAD 47
- PAR T 12: USER OPERATION 48
- 12.2 PROGRAMMING ACCESS CODES 49
- 12.4 REGULAR ARMING 50
- 12.5 STAY ARMING 50
- 12.6 INSTANT ARMING 50
- 12.7 FORCE ARMING 51
- 12.9 ONE-TOUCH ARMING 51
- 10-ZONE LED KEYPAD: 52
- 12.15 KEYPAD MUTING 53
- FCC WARNINGS 54
- SPECTRA SERIES 53 55
- SPECTRA SERIES 55 57
- IN CANADA 02/2003 17X8-EI07 60
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.592 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern