SEKURE Paradox Digiplex DGP-610 Installationsanleitung PDF herunterladen (Seite 41)

EVO Control Panel 37

Figure 20: Example of a Schedule Tolerance Window

The Schedule Tolerance Window applies to Access Schedules only

(see section 15.6 on page 36). and not to the Arming and Disarming

Report Schedules (see section 9.3.1 on page 23).

15.10 Door Access Mode

SECTION [2251] TO [2282]: OPTION [1]

Access Door and user can be assigned to one or more partitions in the

security system. Actions performed by the user will be directly linked to the

partition(s) assigned to that door. Doors 01 to 32 are programmed in

sections [2251] to [2282] respectively.

15.11 Code Access

SECTION [2251] TO [2282]: OPTION [2]

Code Access can allow access to an Access Door by entering a valid user

access code and pressing the [

ACC] key on a EVO641 LCD Keypad instead

of using the Access Card. The control panel will verify its assigned Access

Level and Schedule. Doors 01 to 32 are programmed in sections [2251] to

[2282] respectively.

This option is not available for LED and Grafica Keypads.

15.12 Card and Code Access

SECTION [2251] TO [2282]: OPTION [3]

The Access Door can be programmed to require a user to present a valid

Access Card and then enter the user’s valid code on a DGP-R915 that is

connected to an Access Control Module (DGP-ACM12). The DGP-R915

and the Access Control Module must be correctly configured. Please refer

to the DGP-R915 “Installation and Operating Instructions”, and to the

Access Control Module “Reference & Installation Manual” for instructions.

Doors 01 to 32 are programmed in sections [2251] to [2282] respectively.

When option [3] is enabled, the Access Card must be presented

before the user access code is entered.

15.13 Skip Exit Delay When Arming With Access Card

SECTION [3038]: OPTION [6]

(default = disabled) When arming with an Access Card, the system can

arm with or without starting the Exit Delay.

15.14 Restrict Arming on Door

SECTION [2251] TO [2282]: OPTION [4]

With option [4] ON, the control panel can prevent an Access Card from

arming the partition(s) assigned to the door even if the Access Card is

programmed to permit arming.

15.15 Restrict Disarming on Door

SECTION [2251] TO [2282]: OPTION [5]

With option [5] ON, the control panel can prevent an Access Card from

disarming the partition(s) assigned to the door even if the Access Card is

programmed to permit disarming.

15.16 Door Access During Clock Loss

SECTION [3038]: OPTION [8]

(default = disabled) If the system registers a Clock Loss Trouble, the

control panel will no longer recognize the Schedules until the clock is reset.

Enable or disable the option as required:

15.17

Burglar Alarm On Forced Door or Door Left Open

SECTION [3038]: OPTION [5] (FORCED DOOR)

ECTION [3038]: OPTION [7] (DOOR LEFT OPEN)

(default = disabled) If an Access Door is forced open or left open, a signal

can be sent to the control panel to trigger the burglar alarm. The burglar

alarm is generated instantly regardless of the zone’s definition.

For these features to function:

• Install a door contact and connect it to the door’s Access Control Module

• Assign the Access Control Module to a zone (see Zone Programming on

page 9)

• Enable option [5] in section [3038]: Burglar Alarm on Forced Door

• Enable option [7] in section [3038]: Burglar Alarm on Door Left Open

15.18 Logging Access Control Events

15.18.1 Log Request For Exit In Event Buffer

SECTION [3038]: OPTION [2]

(default = disabled) When enabled, the control panel can record the REX

events generated from all the Doors in the Event Buffer, but cannot report

these events to the monitoring station. The events can be viewed by

entering the Event Record Display.

Since REX events can occur often, the Event Buffer may fill up quickly.

15.18.2 Log Door Left Open Restore In Event Buffer

SECTION [3038]: OPTION [3]

(default = disabled) When enabled, the Door Left Open Restore event can

be recorded in the Event Buffer. These events cannot be reported to the

monitoring station, but can be viewed by entering the Event Record Display.

15.18.3 Log Door Forced Open Restore In Event Buffer

SECTION [3038]: OPTION [4]

(default = disabled) When enabled, the Door Forced Open Restore event

can be recorded in the Event Buffer. This event cannot be reported to the

monitoring station, but it can be viewed by entering the Event Record

Display.

[1] ON

“OR” Access Door

The Access Door grants access or permits arming or

disarming to users assigned to at least one of the door’s

partitions. An “OR” door will arm or disarm only the

partitions that it has in common with the users.

[1] OFF

“AND” Access Door

The Access Door grants access or permits arming only to

users assigned to all the door’s assigned partitions.

[2] ON [ACC] key enabled

[2] OFF Access with Card only

[3] ON Access Card AND User Access Code required

[3] OFF Access Card OR User Access Code

[6] ON The Exit Delay is cancelled

[6] OFF The Exit Delay is triggered

User’s assigned Schedule is 9a.m. to 5p.m. When ‘Add Tolerance Windows to

Schedules’ is enabled for the user, the user has access from 8a.m. to 6p.m.

Schedule Tolerance Windows

Option Until the Clock is reset, access can be granted to:

[8] ON

The System Master or User Access Code with Master

feature or Schedule 00 (00 = all times) enabled

[8] OFF All users regardless of their programmed Schedules

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

SEKURE Paradox Digiplex DGP-610 Installationsanleitung Seite 41

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme SEKURE Paradox Digiplex DGP-610