SEKURE DGP2-648 Installationshandbuch PDF herunterladen (Seite 13)

DIGIPLEXNE CONTROL PANEL 11

3 PROGRAMMING METHODS

DigiplexNE can be programmed using the following methods:

3.1 WINLOAD UPLOADING/DOWNLOADING SOFTWARE*

We highly recommend programming the control panel with WinLoad as it

greatly simplifies the process and reduces potential data errors. Refer to

Winload Software on page 41 for details.

* UL Note: Not verified by UL

3.2 PARADOX MEMORY KEY (NOT TO BE USED WITH UL LISTED SYSTEMS)

The Paradox Memory Key can copy the programmed contents of one

control panel into as many others as needed. Downloading is completed in

less than 5 seconds.

Copy to Memory Key

1) Place the Memory Key on the control panel’s

connector labeled

MEM KEY. Make sure that the write

protect jumper is on.

2) Enter section:

[4020] to copy the control panel’s contents except

sections [0001] to [0096] and [0501] to [0532] to the

key.

[4021] to copy the control panel’s contents

including sections [0001] to [0096] and [0501] to [0532] to the key.

3) When the keypad emits a Confirmation Beep, remove the Memory

Key. Remove the jumper to prevent accidentally overwriting the

Memory Key’s contents.

Download to Control Panel

1) Place the Memory Key on the control panel’s

connector labeled

MEM KEY.

2) Enter section:

[4010] to download the Memory Key’s contents

except sections [0001] to [0096] and [0501] to

[0532] to the control panel.

[4011] to download the contents of the Memory Key

including sections [0001] to [0096] and [0501] to

[0532] to the control panel.

3) When the keypad emits a Confirmation Beep, remove the Memory Key.

Figure 3-1: Using the Memory Key

3.3 MODULE BROADCAST

Keypads and other modules can also be programmed easily by using

Module Broadcast (see section 11.15 on page 33). Once a module is

programmed, its sections can be sent to other similar modules through the

combus.

3.4 PROGRAMMING THROUGH A KEYPAD

Use the Programming Guide to record how the sections were programmed.

To enter programming mode:

For LCD Keypads: The control panel will save the data and automatically

advance to the next section or press the [

ENTER] key to save the data and

advance to the next section. Press the [

CLEAR] key to revert to the

preceding step or to erase the current data entry.

For Grafica Keypads: After entering the required data, press Grafica’s

center action key (Save) to save the data and advance to the next section.

Press the right action key (Exit) to revert to the preceding step or press the

left action key (Clear) to erase the current data.

3.4.1 Feature Select Programming

Most of the options are programmed using the Feature Select Method.

For LCD Keypads:

Each number from 1 to 8 corresponds to a specific

feature or option. Set these options by turning the number corresponding to

the feature ON or OFF. The option is considered ON when the number

appears within the brackets on the LCD keypad. Turn options ON and OFF by

pressing the corresponding keys on the keypad. Press the keys as many

times as needed to select the desired options and then press

[

ENTER

]

to save.

For Grafica Keypads: Select or clear the check boxes pertaining to the

options or features that you wish to enable or disable. You can also set the

options by pressing the corresponding keys on the keypad. The feature is

considered ON when its check box is selected. To save the settings, press

the Grafica’s center action key (Save).

3.4.2 Decimal Programming

Certain sections may require the entry of a 3-digit decimal value from 000

to 255.

3.4.3 Hexadecimal Programming

Certain sections may require the entry of one or more Hexadecimal values

from 0 to F. Press:

For LCD Keypads:

[0] to [9] = values 0 to 9 respectively

[

STAY] key = A [DISARM] key = D

[

FORCE] key = B [BYP] key = E

[

ARM] key = C [MEM] key = F

For Grafica Keypads:

[0] to [9] = values 0 to 9 respectively

[#] = A to F (press the key until the desired letter appears)

3.5 MODULE PROGRAMMING MODE

All modules are programmed through any LCD or Grafica keypad in the

system. To do so, enter Module Programming Mode:

The control panel will redirect all programming to the selected module. To

exit the Module Programming Mode, press the [

CLEAR] key on LCD

keypads, or the right action key (Exit) on Grafica keypads, as many times

as needed to return to the desired screen. The module's serial number can

be located on the module's PC board.

Jumper ON =

Can copy and download

contents of the Memory Key

Jumper OFF =

Cannot override contents

of the Memory Key

1) Press and hold the [0] key

2) Key in the [

INSTALLER CODE] (Default is 000000)

3) Key in the 4-digit [

SECTION]

4) Key in required [

DATA]. Refer to the Programming Guide or to the

corresponding sections in this manual.

1) Press and hold the [0] key

2) Key in the [

INSTALLER CODE] (Default is 000000)

3) Key in section [4003]

4) Key in 8-digit [

SERIAL NUMBER] of the module

5) Key in 3-digit [

SECTION] and required [DATA]. Refer to the Module

Programming Guide for details.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

SEKURE DGP2-648 Installationshandbuch Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme SEKURE DGP2-648