SEKURE DGP2-648 Installationshandbuch PDF herunterladen (Seite 23)

DIGIPLEXNE CONTROL PANEL 21

7 ALARM OPTIONS

7.1 BELL/ALARM OUTPUT

(Default = only option [1] enabled) When an alarm condition is detected in a

partition, the control panel can toggle the on-board

BELL output enabling

any bells or sirens connected to it. In section [3032] enable the option to

enable the bell output in the desired partition (off = disabled):

7.2 BELL CUT-OFF TIMER

(Default = 004) After an audible alarm, the bell or siren will stop once the

partition is disarmed or when the Bell Cut-Off Timer has elapsed. Enter any

value between 001 and 255 minutes:

7.2.1 No Bell Cut-Off on Fire Alarm

SECTION [3030]: OPTION [2]

(Default = disabled) The control panel can disable the Bell Cut-Off Timers

when alarms are generated from zones defined as Standard or Delayed

Fire Zones (see section 4.3). The

BELL output will remain enabled until a

user disarms the partition in alarm.

7.2.2 Recycle Alarm Rate

(Default = 000) The control panel re-verifies the zone status during an

alarm at a programmed rate once the Bell Cut-Off Timer and the Recycle

Delay elapse. If open zones remain, the control panel will regenerate the

alarm. Enter the number of times from 001 to 255 (000 = no limit) in one

armed period that the control panel will re-verify the zone status:

7.2.3 Recycle Delay

(Default = 000) The Recycle Delay is the amount of time the control panel

will wait after the Bell Cut-off occurs before re-verifying the zone status.

Program the Recycle Delay from 001 to 255 minutes (000 = disabled):

7.3 WIRELESS TRANSMITTER SUPERVISION OPTIONS

ECTION [3034]: OPTIONS [1] AND [2]

When the control panel detects a Supervision Loss (wireless receiver no

longer receiving signals from a wireless transmitter), the control panel can

generate an alarm and/or trouble, as shown in the table below, unless the

Wireless Transmitter Supervision Option is disabled.

The Supervision feature must be enabled in the Omnia Wireless

System (OMN-RCV3) for this feature to function.

7.3.1 Supervision Bypass Options

SECTION [3034]: OPTION [3]

(Default = disabled) With option [3] enabled in section [3034], the Wireless

Transmitter Supervision Options will follow the zone's bypass definition.

This means that the control panel will not perform any action if a

supervision loss occurs on a bypassed zone. With option [3] disabled, the

control panel will ignore the bypass definition and will follow the option set

in section 7.3 if a supervision loss occurs on a bypassed zone.

7.4 POLICE CODE TIMER

(Default = 000) If an alarm condition occurs on a zone, the control panel

generates an alarm and triggers the Police Code Timer. The Police Code

Timer requires confirmation of the alarm situation within the delay before

sending the Police Code programmed in [3934]. The Police Code will only

be sent if one of the following conditions occurs during the delay:

1) An alarm occurs on another zone.

2) The zone in alarm restores and reoccurs.

Key in the desired 3-digit delay value (001 to 255 minutes, 000 = disabled)

into the section corresponding to the desired partition:

7.5 TAMPER RECOGNITION OPTIONS

ECTION [3034]: OPTIONS [5] AND [6]

When the control panel detects a tamper or wire fault on a zone or on an

expansion module, the control panel can generate an alarm and/or trouble,

as shown in the table below, unless the Tamper Recognition Option is

disabled.

Partition 1: Option [1] Partition 5: Option [5]

Partition 2: Option [2] Partition 6: Option [6]

Partition 3: Option [3] Partition 7: Option [7]

Partition 4: Option [4] Partition 8: Option [8]

Partition 1: [3113] Partition 3: [3313] Partition 5: [3513] Partition 7: [3713]

Partition 2: [3213] Partition 4: [3413] Partition 6: [3613] Partition 8: [3813]

Partition 1: [3117] Partition 3: [3317] Partition 5: [3517] Partition 7: [3717]

Partition 2: [3217] Partition 4: [3417] Partition 6: [3617] Partition 8: [3817]

Partition 1: [3116] Partition 3: [3316] Partition 5: [3516] Partition 7: [3716]

Partition 2: [3216] Partition 4: [3416] Partition 6: [3616] Partition 8: [3816]

Option

Description

[1] [2]

OFF OFF

Disabled (Default):

Displays zone open on the keypads, but will not generate an

alarm or trouble.

Not permitted on UL systems.

OFF ON

Generates Trouble Only (when armed or disarmed):

The control panel displays Zone Fault in the Trouble Display

and transmits the defined report code (see section 8.2).

ON OFF

When disarmed: Generates Trouble Only

The control panel displays Zone Fault in the Trouble Display

and transmits the defined report code (see section 8.2).

When armed: Follows Zone Alarm Type

The control panel follows the zone’s alarm type (see section

4.5.5 on page 15).

ON ON

When disarmed: Generates Audible Alarm

The control panel displays Zone Fault in the Trouble Display,

transmits the defined report code (see section 8.2), and

generates an audible alarm.

When armed: Follows Zone Alarm Type

The control panel follows the zone’s alarm type (see section

4.5.5 on page 15).

Partition 1: [3118] Partition 3: [3318] Partition 5: [3518] Partition 7: [3718]

Partition 2: [3218] Partition 4: [3418] Partition 6: [3618] Partition 8: [3818]

Option

Description

[5] [6]

OFF OFF

Disabled (Default):

Displays zone open on the keypads, but will not generate an

alarm or trouble.

Not permitted on UL systems.

OFF ON

Generates Trouble Only (when armed or disarmed):

The control panel displays Zone Fault in the Trouble Display and

transmits the defined report code (see section 8.2).

ON OFF

When disarmed: Generates Trouble Only

The control panel displays Zone Fault in the Trouble Display and

transmits the defined report code (see section 8.2).

When armed: Follows Zone Alarm Type

The control panel follows the zone’s alarm type (see section

4.5.5 on page 15).

ON ON

When disarmed: Generates Audible Alarm

The control panel displays Zone Fault in the Trouble Display,

transmits the defined report code (see section 8.2), and

generates an audible alarm.

When armed: Follows Zone Alarm Type

The control panel follows the zone’s alarm type (see section

4.5.5 on page 15).

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

SEKURE DGP2-648 Installationshandbuch Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme SEKURE DGP2-648