SEKURE DGP2-641 Installationshandbuch PDF herunterladen (Seite 21)

IGIPLEX

NE C

ONTROL

ANEL

5.5.5 Alarm Types

5.5.6 Intellizone

(Default = 010) If an alarm condition occurs on a zone with option [7]

enabled, the control panel triggers the Intellizone Delay and seeks

confirmation of the alarm situation before generating an alarm. Fire Zones

cannot be set as Intellizones. An alarm will only be generated if one of the

following conditions occurs during the Intellizone Delay:

1) An alarm occurs on another zone defined as Intellizone.

2) The zone in alarm restores and reoccurs.

3) The zone stays in alarm for the entire Intellizone Delay.

Key in the desired 3-digit delay value (010 to 255 seconds) into the section

corresponding to the desired partition (000 = 10 seconds):

5.5.7 Delay Before Alarm Transmission

(Default = 000) When an alarm condition occurs on a zone with option [8]

enabled, the control panel activates the bell output, but will not report the

alarm to the Monitoring Station until the end of the Alarm Transmission

Delay. During this period, disarming the system cancels any report

originating from this zone. To program the Alarm Transmission Delay, key in

the desired value (000 to 255 seconds, 000 = instant) into section [3055].

This feature is commonly used with Entry Delay zones to reduce false

alarms created by new users who may not disarm the system in time.

5.6 I

NPUT

PEED

(001 to 255 X 30msec default: 600ms)

The Input Speed defines how quickly the control panel responds to an open

zone detected on any hardwired input terminal (does not apply to

addressable motion detectors and door contacts with GuardWall

technology). All other zone definitions and options do not come into effect

until the Input Speed elapses. The control panel will not display and/or

respond to an open zone until the Input Speed elapses to prevent glitches

from causing an alarm or unnecessary reporting.

For example, if an armed zone with an Input Speed of 600ms opens and

closes in less than 600ms, the control panel will not respond (i.e. no

reporting, no alarm and no display on the keypad).

Set the Input Speed (001 to 255 X 30ms, default = 600msec.):

Set the Input Speeds for the optional 4-Zone Hardwire Module, DGP2-ZX4:

5.7 EOL

ARDWIRE

ONES

(Default = disabled) If detection devices connected to hardwired input

terminals use 1k

Ω

end of line resistors, enable option [7] in section [3033].

For details on using EOL resistors, refer to Addressable Zone Connections

on page 12 and Double Zone Connections on page 13.

5.8 K

EYPAD

UMBERING

Keypad Numbering is only used to identify the keypad in the event buffer.

When Keypad Numbering is not used, the event buffer will then display any

events pertaining to any keypad as Keypad 00. When Keypad Numbering

is used, each keypad is identified by a specific number. The keypad is

assigned to a Keypad Number from 1 to 32 through the keypad's serial

number in sections [2801] to [2832]. Enter the 8-digit serial keypad serial

number in the desired section.

Option Feature Description

[5] [6]

OFF OFF

Steady Alarm

sends the report code and activates the bell

output

ON OFF

Pulsed Alarm

sends the report code and pulses the bell output

(see Figure 5-4 on page 18)

OFF ON

Silent Alarm

sends the report code, but the bell output is not

activated. Partition must be disarmed.

ON ON

Report Only

sends the report code. Disarming is not required.

Fire Zones cannot be Report Only.

Partition 1: [3110] Partition 3: [3310] Partition 5: [3510] Partition 7: [3710]

Partition 2: [3210] Partition 4: [3410] Partition 6: [3610] Partition 8: [3810]

Section Input Section

[0961] Input 01 [0973] Input 13 (ATZ of Input 01)

[0962] Input 02 [0974] Input 14 (ATZ of Input 02)

[0963] Input 03 [0975] Input 15 (ATZ of Input 03)

[0964] Input 04 [0976] Input 16 (ATZ of Input 04)

[0965] Input 05 [0977] Input 17 (ATZ of Input 05)

[0966] Input 06 [0978] Input 18 (ATZ of Input 06)

[0967] Input 07 [0979] Input 19 (ATZ of Input 07)

[0968] Input 08 [0980] Input 20 (ATZ of Input 08)

Section Input

[0969] Input 09 (DGP2-ZX4 Input 01)

[0970] Input 10 (DGP2-ZX4 Input 02)

[0971] Input 11 (DGP2-ZX4 Input 03)

[0972] Input 12 (DGP2-ZX4 Input 04)

[0981] Input 21 (ATZ of DGP2-ZX4 Input 01)

[0982] Input 22 (ATZ of DGP2-ZX4 Input 02)

[0983] Input 23 (ATZ of DGP2-ZX4 Input 03)

[0984] Input 24 (ATZ of DGP2-ZX4 Input 04)

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 65 66

Kommentare zu diesen Handbüchern

Keine Kommentare

SEKURE DGP2-641 Installationshandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme SEKURE DGP2-641